One controller · real-time water intelligence · one route at a time
Smart water, single-minded
Water that thinks ahead.
Walter connects your source and storage tanks with one intelligent ESP32 controller that measures, decides, protects, and keeps you in the loop—wherever you are.
One ESP32 controllerDual tank monitoringTreatment-aware routing
Walter control coreIllustrative view
Source tank
56%Reserve protected
Storage tank
68%680 L available
TDS signalReady
Selected routeDirect
Pump stateStandby
Tank level insight
Two intentional routes
Usage & status trends
Safety-first automation
The Walter way
One brain. A clearer flow.
Walter is a single-node architecture. One ESP32 controller turns calibrated sensor readings into a safer, more understandable water routine—without needing three separate nodes.
The calm center of your water system.
Single controller
The controller sees both tanks, reads the source water before the branch, and publishes useful status to the Walter app. It makes the local safety call before any pump runs.
Storage level
Ultrasonic readings estimate how much water is ready for use.
Source reserve
The source tank is checked before—and while—water is transferred.
TDS signal
A current TDS reading selects the configured water route.
Measure → check → choose one route → report
Local first
The device decides what is safe.
A request from the app is just that: a request. The controller still checks sensor freshness, source reserve, tank limits, settings and pump progress.
Useful, not noisy
See the water story.
Live status, recent usage estimates, alerts, route decisions and device health stay visible in the connected Walter experience.
Treatment-aware routing
Water follows the right route.
The TDS sensor reads the source water before the branch. Walter then chooses one pump route for the fill according to your unit’s configured threshold—never both at once.
01
Direct to the tank
When the source-water TDS reading is below the configured routing threshold, Walter selects Pump 1 and sends water directly to the storage tank.
Source water→Pump 1→Storage tank
The exact threshold is calibrated and confirmed for each installation.
02
Through the treatment path
When the reading is at or above the configured threshold, Walter selects Pump 2 to send water through your installed sediment-filter or treatment path before it reaches the tank.
Source water→Pump 2→Treatment path→Tank
Your filter and treatment equipment are part of the installation—not a software afterthought.
Protection in every decision
Built to pause before trouble.
Walter is designed to leave both pumps off when the system does not have the information or conditions it needs. It helps prevent guessing at the wrong moment.
Unknown means stop
If required tank or TDS readings are invalid, missing or stale, Walter blocks a new fill and can stop an active one.
Source reserve protected
A fill is refused or stopped when the source tank reaches the configured reserve, helping protect against dry-run conditions.
Full tank, pumps off
Walter checks the receiving tank’s configured fill-stop level before allowing the selected pump to run.
Progress is checked
During a transfer, Walter checks that tank level is rising as expected. A failed flow check can stop the pump and raise a fault lockout.
Requests are acknowledged
The app can request a start or stop, but the controller reports the actual motor state and stop reason after its local checks.
Connected when available
Wi-Fi shares readings, alerts and settings with the app. If a device is offline, the last cloud reading is history—not a guarantee of current conditions.
The Walter customer app
Your water system, in your hand.
View your latest levels and device health, follow usage trends, understand alerts, review the selected route, and make supported pump-control requests—while Walter’s local safety checks stay in charge.
Everything we say about Walter is grounded in what the single-controller system can actually monitor and do.
Not this Walter. The current setup is built around one ESP32 controller that coordinates both ultrasonic level sensors, the TDS sensor, two alternative pump relays, local display/audio, Wi-Fi, settings and status reporting.
Walter measures TDS in the source water before the pump branch. Below the configured threshold, it selects Pump 1’s direct route. At or above the threshold, it selects Pump 2’s installed treatment path. The two pump routes are alternatives; the controller does not intend to run them together.
No. TDS is not a drinking-water safety test and cannot identify all contaminants, chemicals or microbes. A sediment filter or treatment path must be properly selected, installed, maintained and independently validated for your intended water use.
An authorized user can make a supported start or stop request. The controller checks local conditions first and may refuse or stop the transfer. Check the acknowledged device status in the app rather than treating a sent request as proof that a pump ran.
Cloud updates can become delayed while Wi-Fi is disconnected. For local filling, missing or stale required readings cause Walter to block a new transfer or stop an active one instead of choosing a route from unknown conditions.
Water, with more clarity
Move with the flow. Know what’s behind it.
Open your Walter app to see the latest reported state of your connected system, or explore how an intelligent water routine can fit your space.